A password will be e-mailed to you.

When I moved to Singapore around 5 years ago I created my first IKEA hack by combining two LACK TV Benches and the sides from a LACK TV Side Table to create a larger tv unit. Having recently moved into a new apartment it was time for a new TV cabinet.

I looked at several TV cabinet options in Singapore but could not find anything that was just what I was looking for in terms of size, design, and price. Therefore, I decided to create another IKEA hack.

Initially, I was planning to combine four fridge top cabinets similar to the hack posted by Med Venlig Hilsen. However, after further research of the IKEA catalogue, I decided to use a single high kitchen cabinet placed on its side rather than joining four fridge top cabinets together. Here’s how I hacked a TV cabinet out of a METOD high cabinet.

IKEA items used:
  • IKEA METOD High cabinet 200cm
  • IKEA KUNGSBACKA Door 140x40cm
  • IKEA KUNGSBACKA Door 60x40cm
  • IKEA UTRUSTA Shelf 40x60cm (Pair) x3
  • IKEA UTRUSTA Ventilated Shelf 60x60cm
  • IKEA UTRUSTA large hinge for horizontal door in black (Pair) x2
  • IKEA UTBY stainless steel legs (Pair) x4
  • IKEA BLANKETT Handles 595mm (Pair)
Other materials and tools:

Hack instructions for METOD high cabinet to TV cabinet:

Before starting the project I put together a quick 3D sketch to help me visualize the finished TV cabinet.

TV cabinet from IKEA METOD kitchen cabinet

Base Preparation:

Once assembled this TV cabinet was going to be a sizable and heavy piece of furniture. Therefore, I tried to build it as close to the final location in my living room as possible so as to minimize the number of times that I would need to turn it or move it.

As a result, I started building the TV cabinet from the ground up. The first task was to drill a hole in the base for cable entry. I drilled a 64mm diameter hole in the center of the base with the IKEA FIXA hole saw set. This 64mm hole is large enough that a stranded UK three pin plug can pass through it.

If your country has more compact power plugs you could drill a smaller diameter hole. I drilled the hole through from both sides to minimize any break outs. I then pained the cut edge with black paint for a more pleasing aesthetic finish.

TV cabinet from IKEA METOD kitchen cabinet

Leg Installation:

The next task was to turn the base over and to install the four IKEA UTBY stainless steel legs at the corners of the cabinet base.

As I would be placing a significant amount of equipment inside the cabinet and a large 60″ television on top of it I also installed four additional IKEA UTBY stainless steel legs in the middle.

The front legs are set back so that they would be hidden and the finished TV cabinet would have a clean and sleek appearance.

However, these additional legs provide the required strength to support the weight to be placed inside and on top of the cabinet and are positioned directly under the columns that would support the top.

TV cabinet from IKEA METOD kitchen cabinet

TV cabinet from IKEA METOD kitchen cabinet

Shelf Preparation:

I started by opening all of the IKEA UTRUSTA shelves and laying them out the six pieces on the floor.

I then used post-it notes to label the inside face and front/top edge of each panel for easy reference.

In order to ensure that I drilled the holes in these six shelves correctly, I created a table and diagram to document which shelf required each set of holes.

TV cabinet from IKEA METOD kitchen cabinet

I then created a template showing where all of the different holes should be drilled so as to ensure consistent alignment across all of the shelves. The light grey box in the upper left-hand corner represents the UTRUSTA hinge. There was just enough space above the hinge for the corner block to be installed.

TV cabinet from IKEA METOD kitchen cabinet

Preparing the Shelves – Part 1 (Cable Holes):

In order the provide additional strength to the cabinet and support the weight of the TV I used pairs of IKEA UTRUSTA shelves located around 60cm in from the left and right end of the cabinet. To enable cables to pass between the three compartments I drilled a 64mm hole in the lower part of each shelf. I then used back paint to cover the inner edges of the holes.

Preparing the Shelves – Part 2 (Equipment Shelf):

For most of the cabinet, I would use the full height due to the size of my equipment and the requirement for good cooling in the warm climate of Singapore. However, I decided to install one horizontal shelf on the right-hand side to maximize internal storage for slimmer equipment.

For this, I used the IKEA UTRUSTA Ventilated Shelf as this had a gap at the back allowing me to route cables between the upper and lower sections without making modifications to another full depth shelf. This shelf would be supported on four black corner blocks.

Preparing the Shelves – Part 3 (Supporting Columns):

Shelves 2 & 3 and 4 & 5 were fixed together using wood glue to create strong columns capable of supporting the weight of the television to be placed on top of the finished cabinet. I would also add an extra vertical shelf to each end of the cabinet for greater strength that would be attached during the assembly using wood glue.

Preparing the Shelves – Part 4 (Hinge Holes):

For my design I wanted to the doors to open upwards rather than sideways, therefore I needed to use the IKEA UTRUSTA large hinge for horizontal doors. However, as the high cabinet was designed to have regular hinges installed on the sides (now top and bottom) I needed to mount these hinges to the vertical IKEA UTRUSTA shelves. I had previously purchased an IKEA METOD fridge top cabinet so I used this as a template to measure the location of the required mounting holes.

Preparing the End Panels:

Unfortunately, the end panels of the cabinet have a number of holes drilled in them that would in the original vertical orientation have had adjustable legs attached to them. This would look ugly if left exposed on the ends of my TV cabinet. Therefore, I reversed the panels so that these holes would be on the inside of the cabinet. The outside was clean with the exception of a vertical recess that the back panel would normally slot into. I painted this recess with black paint so it would be almost invisible once installed in the finished cabinet.

Installing the Shelves (aka Columns):

I worked from right to left adding the shelves. I used the horizontal ventilated shelf to correctly position the right-hand column. An additional shelf was placed inside the right-hand end panel to ensure the correct positioning. The horizontal shelf would be installed later after the top had been installed to provide better access. Then the left-hand column was installed. Each column was installed using 4 black plastic corner blocks.

TV cabinet from IKEA METOD kitchen cabinet

Top Preparation:

You could feed the cables to your TV through the back of the cabinet. However, I want the finished TV cabinet to sit flush against the wall so this was not an option. Therefore, it was necessary to make holes in the top of the cabinet.

I purchased a black metal cable outlet from eBay in Germany: SO-TECH Cable Pass-Through Table Duct (200 x 70 mm). After drilling a series of holes using a 4mm drill around the outside of the cutout I used a fret saw to remove the wood between the holes and some sandpaper to smooth off any edges. There was only a 5mm overlap on the cable outlet so I had to be careful not to make the hole too large. Then I used some black paint to hide the inner edges of the hole.

Installing the Back Panel:

As I had reversed the end panels to hide the holes the recess that the back panel would normally slot into is now on the outside of the cabinet. Therefore, I had to reduce the width of the back panel so that it would fit. With the intention to have my cabinet positioned flush against the wall I needed to make some extra holes in the back panels to accommodate the plug sockets and in particular my bulky power line network extender.

I marked up the back panel and drilled a 10mm hole in the corners. I then used a fret saw to cut out the sections to be removed. The back panel was installed using a combination of the supplied nails and wood glue to provide additional strength to the cabinet.

Top and Horizontal Shelf Installation:

The cabinet top panel was installed using the standard parts. Then an additional shelf was glued inside each end panel to provide greater strength and to cover up the leg holes in the end panels. The two supporting columns were also attached to the top using more black plastic corner blocks.

The IKEA UTRUSTA Ventilated Shelf was installed using a single screw in the front corner blocks to prevent it being pulled out if I needed to remove any of my equipment. At this point, I had a good view of how the final cabinet would look.

TV cabinet from IKEA METOD kitchen cabinet

Putting everything together:

The doors were attached to the UTRUSTA large hinge for horizontal door with the black covers fitted. The hinges supporting the longer door on the right of the cabinet required the tension to be increased so that they could support the weight of the door. To improve the visual appearance of the cabinet doors I added the BLANKETT metal handles to the bottom edges of the doors. I went for the longest versions that would fit my smaller cabinet door (595mm) to emphasize the long and low design of my TV unit. The final step was to install all of my equipment and to place my TV on the top.

TV cabinet from IKEA METOD kitchen cabinet

See more of the METOD turned TV cabinet on my blog.

~ by James Evans