Bedroom

Published on April 28th, 2012 | by Jules IKEAHacker

17

EXPEDIT Bed Frame





Materials: (2) EXPEDIT 5X1 Shelving unit’s, FIXA floor protectors, (2) sheets MDF, (1) 4X4 post, wood screws, power drill

Description: While spending some time in the US, I wanted to show my brother the potential of IKEA furniture. A few days later, I surprised him with a modern, functional upgrade to his bed.I wanted to provide adequate storage in a room with minimal space. My idea was to take advantage of the DRONA boxes in conjunction with the EXPEDIT shelves.


Step 1: Using the completed EXPEDIT unit, I was able to take proper measurements for the EXPEDIT unit that needed to be trimmed down.

Step 2: Cutting the EXPEDIT to the correct size. For in-depth information on this part of the process, please visit this instructable.

Step 2.5: The extra material from this step can be used for various items. In our case, we used the extra pieces to provide numerous shelves throughout the space.

Step 3: With both finished EXPEDIT units, I was able to take measurements for the MDF. Due to my situation, one piece of MDF was not enough to completely support the bed. At this point, you can also measure the correct height of your 4×4 wooden post supports. This supports will placed under the MDF for added support.

Step 4: This is an optional step. Depending on the type of bedding used, some of the MDF support layer can be visible. As I was pinched for time, my father recommended the fastest fix all solution: Duct Tape! As many know, Duct Tape comes in a variety of colors. My local home improvement store happened to have a roll of black. We covered the edges of the MDF to blend this portion with the EXPEDIT unit. If you have more time, I would have went with a painted MDF.

Step 5: Using FIXA floor protectors, I covered key points on the EXPEDIT units and the 4X4 posts to prevent the flooring from being damaged. It also prevented the MDF from damaging the EXPEDIT surface.

Step 6: With all the pieces completed, it’s time for final assembly. The EXPEDIT’s should be set in place first. Next, we set the 4×4 support posts in their location. From here, you can bring in the MDF sheets. With the MDF in place, you can then move forward with attaching the MDF to the 4×4 posts.

Step 7: For extra support, brackets can be used to attach the MDF to the EXPEDIT 5×1 ONLY. ** DO NOT attach anything to the EXPEDIT 2×1 unit ** The 2×1 unit is a free floating piece. It can be removed to enable more storage under the actual bed frame for the user(several plastic bins fit well in this space).

Step 8:Lastly, place the mattress on the MDF.

Sadly, our local IKEA’s were sold out of the DRONA boxes in black. The bins pictured can purchased at “The Red Bulls-eye”

~ RJ Caraynoff

Updated: 1 May 2012

Maximilian’s version for a Queen bed

When I moved in my new flat I had a smaller room than before. I needed a place where I could store all my LPs and I needed storage under my bed. When I measured the Expedits I found that they are perfect for LPs and I decided to use them to build my bed.

What you see on the pics is the finished bed (don’t look at those cables, I didn’t yet have the time to let them disappear). My first idea was to have an open corner which than would be covered with milked acrylic so I could put a lamp behind it to have some nice diffuse light in in my room. But since the Expedits take lots of their sturdiness from those end parts, I decided to ditch that idea for now, especially having in mind that a bed is not always only for sleeping…

I used the “Expedit Bookcase size reduction” instructable to cut them (140x200cm which is queen size in the US I believe). I than used metal brackets to attach it to the wall and to connect both Expedits with each other. After that I put wooden bars at the wall and one in the middle to later hold the slatted frame and the mattress and basically that’s it. So now I have space for all my LPs and enough storage for things I don’t use on a regular basis. The biggest size you could get with two Expedits attached like that would be 180x200cm but I don’t have the space for that.

~ Maximilian

More hacks on IKEAHackers.net
"Ideale" bike rack: Stolmen becomes art!
Coffee Table Coaster Frame

The Author

Jules IKEAHacker

"I am Jules, the engine behind IKEAHackers and the one who keeps this site up and running. My mission is to capture all the wonderful, inspiring, clever hacks and ideas for our much loved IKEA items".

17 Responses to EXPEDIT Bed Frame

  1. Anna says:

    This is a kid/junior bed, right? The Expedit is only 185 cm tall.

  2. MrBishop says:

    I like it, I might have to do something similar. Right now my mattress is sitting on the ground.

  3. Kevduce says:

    Could this be adapted for a queen bed? If so, I’m going for it!

  4. icerabbit says:

    Left out a couple key points (and mdf certainly wouldn’t be my choice for the surface top) but looks practical with plenty of storage.

    If you were to pull the bed away from the wall 1ft / 30 cm you could use two full shelves and gain storage on both sides, without needing to fiddle with posts.

  5. Maximilian says:

    It can be done as a queen bed, just put the other expedit at the end and it adds its 45cm to the 185cm of the other. Makes up for a nice bed. I sent it in here 2 1/2 years ago, but it never got posted.
    Mine is 150cm in width, because I didn’t have the space to hate the whole 185cm. Shorting Expedits can easily be done with the method described at instructables.

  6. How would you do this for a king size bed?

    • Jules says:

      It can be done. Just as how Maximilian did for the queen. (See updated post) Just have to cut the Expedit to the right size.

  7. this is very cool. I’m currently in Paris for a project, and considering the size of the apartments here, this is a great thing to do.

    Thanks for sharing.

  8. bigspud says:

    Thanks for posting this – I was really struggling finding a bed to fit in my son’s small room. But the Expedit is a perfect fit. I’ve only got a single here, so have two Expedits lying side-by-side. It looks brilliant! Thanks again

    http://roastpotato.files.wordpress.com/2012/05/dsc06707.jpg

  9. josh says:

    MAXIMILIAN THAT LP STORAGE BED IS ONE OF THE COOLEST THINGS I’VE EVER SEEN IN MY LIFE! ARE YOU MASS PRODUCING THESE? IF NOT YOU SHOULD BE- EVERYONE WILL WANT ONE!!

    -joshthekook@gmail.com

  10. imajoebob says:

    A little late to the party, but an alternative to Duct Tape or paint is fabric and a staple gun. You don’t need to cover the entire platform, and you can add batting underneath to cushion the edges.

  11. Anonymous says:

    has anyone yet tried a king size version? would love to know how they did it and if it is still sturdy

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

Back to Top ↑

  • Null
    Overlays
    Null
    CoverCouch
    Null

  • Knesting

    Covercouch


  • See the Best of the Best

    See the Best of the Best

Twitter Auto Publish Powered By : XYZScripts.com