Work Station

Published on March 21st, 2008 | by Jules IKEAHacker

10

wardrobe to computer workstation





john was in need of a nice computer wardrobe, and was very frustrated that all the solutions were either too small and shoddy or way too expensive. after some inspiration from this site, he hacks the leksvik 3 door wardrobe into a computer workstation.

he says, “i permanently mounted the main bay shelf at approx 30 inch height and placed horizontal supports under it to give it good support to hold the monitor and be the main work area. i then mounted an adjustable keyboard tray to finish off the main bay.

the smaller bay had 4 shelves in it. i wanted this bay for peripherals, and wanted pull out shelves for easy access. this was accomplished by installing 3 of the shelves permanently with drawer slides i purchased at a local home improvement big box. i ripped the 3 shelves down 2 inches in width, saving 1″ of the width rip for an offset that i mounted to the rightmost side of the wardrobe, and then mounted the drawer slides to that offset which allowed the sliding shelves to clear the doors when they are open.

i used a hole saw to cut 1.5″d holes behind each peripheral shelf, and two in the main bay, one above the work surface and one below it. i cabled in power and USB to each peripheral shelf and was ready to go.

all told the cost was about $70 in random hardware including the keyboard tray for the mod. assembly was a snap. the main unit took about an hour to set up, and the mods took about another 2-3.

i ran into some difficulty with the slide offsets splitting from the wood screws. the reclaimed pine is very sensitive, and i found that countersinking for the screw head is mandatory and solves the splitting problem. tools i used were my trusty dewalt cordless screwdriver, table saw for ripping the shelves down, and a miter saw for cross cutting the the main work shelf supports.

this could all be done with just a manual screwdriver and a hand or hand power saw, but be sure to take appropriate measures to minimize chipout of the shelves if you do.”

More hacks on IKEAHackers.net
elvis is in the house!
a living room makeover

The Author

Jules IKEAHacker

"I am Jules, the engine behind IKEAHackers and the one who keeps this site up and running. My mission is to capture all the wonderful, inspiring, clever hacks and ideas for our much loved IKEA items".

10 Responses to wardrobe to computer workstation

  1. X says:

    Nice, I like the idea.

    But, wouldn’t it be hard to get to the peripherals when you have one door in the way? Now if you could find the way to maybe side the door in to get it out of the way, or fold both door to the left side, that would be very neat.

  2. Michele says:

    Nice – really well-designed, nice looking and functional. Thanks for the assembly details.

  3. Anonymous says:

    Great idea, but I think the middle door would drive me bonkers being in the way when I needed to scan/print something. Better if the doors slid inside or something…

  4. Mackie says:

    the door cannot slide inside as it would need a special compartment to go into,right? and there are the shelves … i guess you can get used to having to work around the door.

    i think it is a very neat hack.

  5. This is wonderful idea. It’s amazing that I have been thinking about doing something similar in my room but never got around. After reading this post I know that it’s possible and hope to get around doing it. Keep it up. This is a wonderful site!

  6. Anonymous says:

    i got a great wardrobe/computer desk from a company called turnstyle ltd in newark england. great quality and very cheap less than £300.

  7. jdevale says:

    The comment about the doors is true — having lived with this now for a year or so it can be frustrating. The truth is though that we only rarely use the peripherals.

    That having been said, it would not be terribly difficult to modify the middle door to slide that completely recesses the door. Instead of mounting the main desk to the right side of the large compartment you put in an internal vertical support for it to connect to. Then depending on the slide design you might have to trim the main door a bit. Now that I think about it it would be fun to do. If I get around to it I will repost.

  8. Anonymous says:

    Nice job.

    I’m thinking of using the same wardrobe as a hall cupboard by just adding further shelves to the double width compartment instead of having the rail there.

    I notice you haven’t put the back on though – I’d be a little wary of that as the back panels are usually there to stabilize the structure.

  9. josh says:

    Hi, just wanna share this

    12 tips for Best Computer Workstation 1. use a good chair with a dynamic chair back and sit back in this
    2. top of monitor casing 2-3″ (5-8 cm) above eye level
    3. no glare on screen, use an optical glass anti-glare filter where needed
    4. sit at arms length from monitor
    5. feet on floor or stable footrest
    6. use a document holder, preferably in-line with the computer screen
    7. wrists flat and straight in relation to forearms to use keyboard/mouse/input device
    8. arms and elbows relaxed close to body
    9. center monitor and keyboard in front of you
    10. use a negative tilt keyboard tray with an upper mouse platform or downward tiltable platform adjacent to keyboard
    11. use a stable work surface and stable (no bounce) keyboard tray
    12. take frequent short breaks (microbreaks)

    Hope this also helps… =)

  10. Wow great idea. We can save lot of space by using this idea.

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

Back to Top ↑

  • Null
    CoverCouch
    Null
    Overlays
    Null

  • Knesting

    Covercouch


  • See the Best of the Best

    See the Best of the Best

Twitter Auto Publish Powered By : XYZScripts.com