Converting an IKEA PS 2014 lamp to resemble the iconic Star Wars’ Death Star is hands down one of the most popular hacks on IKEAhackers.
Star Wars fans can’t resist exploding the Death Star in their own living room.
Many have attempted it with slightly different approaches. Find one that suits your DIY level and own the Death Star.
Buy IKEA PS 2014 lamp, white-copper | IKEA.com
Other materials you may need, depending on the style of lamp you pick:
- Masking tape
- Plastic paint
- Spray paint
- Luminuous paint
- Acrylic paint
- Scalpel / Xacto knife
- Compass for geometry
- Paint brush
A Rugged Star
Naja’s version gives the Death Star a rough, rugged look. It’s also one of the easiest tutorial. First, she masked the parts of the lamp she wanted to keep white with sticky tape. This part is most time consuming.
The laser part was tricky, so she drew the pattern on a big piece of tape and cut it out using a scalpel, then applied it carefully to the lamp. Then, she paint the exposed parts with plastic paint, twice over, to get a good cover. Read more.
A speckled star
Simon spray painted the tiles grey before assembling them. After they were dry, he assembled the lamp and began masking the lines.
Next thing was to use a compass to draw a series of circles to create the laser weapon of the Death Star. After which he began painting the laser rings.
Lastly, using a toothbrush dipped in black paint, he gave the grey areas a speckled look. See full tutorial.
Maria’s Intricate Star
Maria used a can of light grey spray paint from the hardware store to spray the tiles.
If you want to have it perfect — cover the copper insides BEFORE you spray paint the outsides, as the mist of the spray will dull the sheen.
You’ll end up with an light grey ball after assembling it like the instruction tells you.
Then, use masking tape to cover the areas that should stay lighter. Use an X-acto knife and a cutting mat with a ruler to make variations in the strips. Cut some wide, some small, some long, some short. Alternate to create the pattern, the Death Star wasn’t all the same, neither should be yours.
The laser weapon template
Maria then created a stencil of the round laser weapon on a piece of paper. And traced that onto the Lamp with a pencil.
She’s provided a scanned template of the laser in 3 versions. The template was drawn by hand so it was hard to get a clear scan. But you may still be able to use it as a starting point for a template. It fits on a sheet of A4 paper and is meant for the 52 cm diameter version — for the smaller ones you’ll need to size it down.
This step took a good bit of patience but it’s worth to take your time and go wild on details.
Once you’re satisfied with the look of your pattern, you can paint a darker shade of paint over the whole ball.
Maria felt that black was too dark and sharp a contrast, so she mixed a darker grey colour from acrylic paint and a chalk paint. This gives it a not so glossy finish.
Paint the ball completely or work in segments — it all depends on your taste. Lastly, they peeled the masking tape not long after painting.
Make sure to press the tape down well before painting to avoid leaks and blotches. But even if you have some slight uneven lines — the end result will be great. The Death Star has so many little bits and dots, it will look like you wanted it this way 😉
The round weapon was painted by hand with a fine brush.
Hang it on your ceiling as instructed. You will need a hook for that. And enjoy your Death Star lamp. It’s awesome!
~ by Maria
#4 Want a Star?
It took me approximately 20 hours to build, and it is my second build, as somebody has recently purchased my first one. I’ll be more than happy to build more lamps in the future for other people. DM me at [email protected] if you want one.
Additional enhancements to your Death Star lamp
#1 Automate the opening and closing
Forget the pull-strings. Automate the opening and closing of the lamp via an infra-red remote control for the ultimate Death Star explosion. See how it’s done.
#2 Motion sensor lamp
Explode the lamp with a wave of your hand? No problem. Chase’s version of the PS 2014 lamp is activated by motion. View the tutorial.