Bedroom Done-782925

Published on March 14th, 2013 | by Jules IKEAHacker

21

Pax Murphy Bed with Sliding Doors





Materials: Pax Wardrobes and Lyngdal sliding doors

Description: We wanted to make the second bedroom in our condo more multifunctional, and the obvious solution was a Murphy bed.

We spoke to some of the local suppliers, and a basic Murphy bed with no additional storage space would have been at least $3,500. That’s a little steep, and we didn’t really like the style of any of them.

I’d seen two IKEA hacks that used Pax cabinets with a Murphy bed kit here and here.

I used those as inspiration, but switched to sliding doors instead of bifolds.

Materials:

3 Ikea Pax 100×236 wardrobes (1 was cut up and used for materials)
2 sets Ikea Pax Lyngdal 200×236 sliding doors
1 set Ikea Inreda LED spotlight
2 Ikea Inreda LED light strips
Free-standing Murphy bed kit
2″ and 1-1/4″ particle board screws
Cabinet edging tape

Total Cost: $1,650

Ikea Cost: $1,010

We waited until Ikea had a Bedroom event. We bought the Pax stuff, got $150 gift card back, and then used that to buy the lighting. I was also able to scavenge some underutilized shelves and drawers from a few of the other Pax wardrobes we have.

Total Width: approx. 372cm (10′-1″)

From start to finish the project took about 1 week – that was one solid Saturday of work, with everything else done in the evenings.

For the most part all of the work was done by one person, but there were a few steps were a second set of hands was needed: initially assembling the Pax wardrobes; lifting the top piece into place; and lifting the doors onto the rails.

See more of the Pax sliding door wardrobe with Murphy bed.

~ Chris Nelson, Edmonton, Canada

More hacks on IKEAHackers.net
Lack TV Unit (again) Coffee Table
Akurum tip out sponge soap drawer

The Author

Jules IKEAHacker

"I am Jules, the engine behind IKEAHackers and the one who keeps this site up and running. My mission is to capture all the wonderful, inspiring, clever hacks and ideas for our much loved IKEA items".

21 Responses to Pax Murphy Bed with Sliding Doors

  1. Anonymous says:

    I know one must make sacrifices when living in small spaces but, how do you get to your clothes when the bed is down?
    Other than that it looks great!

    • K M Story says:

      This is actually for his second bedroom, so I don’t think getting to his clothes is an issue (I’m assuming that it’s basically a guest bed). Also, it wouldn’t take more than a few seconds to put the bed up and get to your clothes, so I don’t think it would be a problem for whoever is using the room.

    • newfangled says:

      Yup, it’s our guest bedroom which already has its own walk in closet. We’re just using the extra Pax storage for spare bedding, purses, yoga/fitness stuff, boardgames…

      If the bed is down, it takes less than 10 seconds to flip it up and access the storage. It wouldn’t be ideal as a main bed/closet, but it would still be pretty workable.

      The biggest challenge is the width – in the description it says 10′-1″, but I goofed and it’s actually 12′-2″. So you need a fairly long wall to make this work.

    • Anonymous says:

      Thanks for the replies. Didn’t see that it was a guest room.

      @K M Story, I certainly could see it as an issue if someone was still sleeping in the bed. Making sure you have clothes out for the next day would be a necessity if it was the main bedroom and one was part of a couple.

  2. Alek Davis says:

    It looks awesome. Question: which Murphy bed kid did you use?

    • newfangled says:

      I used the Next Bed kit. For a lot of the other kits I saw comments about how flimsy or cheap the foundation for the mattress was, but that’s not an issue with the Next Bed since it uses slats.

      It needs to be mounted to the wall at baseboard level which is what’s covered in the instructions, but I’m pretty sure you could mount it to the floor instead if you wanted.

      There are plenty of videos of it online, like this one: http://youtu.be/B1XIB5PchAI

    • Alek Davis says:

      Good info. Thanks!

  3. Jerry says:

    That looks amazing! Good job!

  4. Oh I love this!

    Sherry Tejada

  5. Anonymous says:

    Does the bedding not get extremely wrinkled whilst it’s up? Or do you just dress it each time you take it down?

    • newfangled says:

      It gets pressed flat against the wall, so it hasn’t really been a problem? It might need to be smoothed out a bit when the bed is pulled down, but nothing major.

      We don’t fold the pillows up, though. We have a 12″ mattress with a mattress pad, which we just reused from our old bed. With a shallower mattress you might be able to fold the pillows up, but with our gigantic mattress they either have to be tucked down on the sides, or pulled off and put in the storage.

  6. newfangled says:

    This comment has been removed by the author.

  7. Lomr says:

    Love this idea, really opens up the space.

  8. This is so retro! I haven’t seen a Murphy bed in forever. I lived in several small studios in NYC and Jersey City during the 90s and Murphy beds never dawned on me. I only wish now I had remembered them then. I was thinking, If you didn’t have sliding doors, you could push the bed up and leave it as is. The underside showing (during a party) might make for a great conversation piece. Or put some nails in the bottom frame and hang art temporarily. Great ikeahack.

  9. Murphy beds are so practical and seem to becoming a lot more popular, especially in apartments, condos and studios. I assembled a queen-size BredaBed for my parents-in-law who live in a small apartment. Very convenient!!

  10. dave says:

    Great idea, which I’ve been studying closely.

    FYI 372cm = approx. 12′-2.5″

  11. Bonnie Gleeson says:

    Is there any chance you could use a king sized mattress in this arrangement? We’ve just decided to do this in our basement level guest bedroom. We already have a king size bed there and would like to keep it but the room would be so much more useful if we had a murphy bed.

  12. Leigh says:

    Just wanted to see if you still enjoy the Next Bed now that you’ve had it awhile and find it comfortable.

    Also, I have a large antique headboard I’d like to use mounted on the wall behind the Next Bed. Is there an reason you see that it wouldn’t work? From everything I see is seems like it would be no problem.

    Also #2, for the space at the head of the bed where there’s a gap…would it work to slip 1 or 2 pieces of very firm foam in that gap once the bed is open?

  13. Nora says:

    Hey! I live in Northern AB and was hoping to find a local dealer for the Next Bed — I’ve found one in Calgary but nothing in Edmonton. Where did you buy yours?
    I love how this looks, great job!

  14. Ngiam Tee Wai says:

    Hi Jules, I’m from Kuala Lumpur, Malaysia and is interested to know where you bought (or where can I buy) the free standing Murphy bed kit and how much it cost. Thanks in advance for your reply.

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

Back to Top ↑

  • Overlays
    Null
    CoverCouch
    Null
    Null
    Null

  • Knesting

    Covercouch


  • See the Best of the Best

    See the Best of the Best

Twitter Auto Publish Powered By : XYZScripts.com