Galant Image+2-707053

Published on February 18th, 2013 | by Jules IKEAHacker

17

Galant Standing Desk with Monitor Shelf





Materials: Galant 160x80cm Desk with Frame, Galant 80x60cm Extension Table with Frame (2), Galant T-Leg (2), 8″ Capita Legs (2), Ekby Hemnes 119x28cm Shelf, 1′ Long 3/8″ Threaded Rod (4), 3/8″ Hex Nut (4)

Description: Inspired by Steev Kelley’s two-level Galant hack, I set out to create my ideal standing desk.

This design provides a 160x80cm upper desk, a 160x60cm lower shelf and a 119x28cm monitor shelf.

I had a lot of fun thinking this out and figuring out what pieces to use. Thanks again to Steev for the original concept.

Step 1 – Assembling the lower frame

In order to match the width of the lower shelf to the upper shelf and still keep it out of the way of my legs, I used two 80x60cm extension tables (901.052.67) and matching extension frames (100.568.88) connected lengthwise.

My intent was to connect the two extension frames to one another and expand them to match the 160×80 frame on the upper desk, but I underestimated the ability of the extension frames to extend that far. By drilling my own holes in the extension bars and using metal screws, I was able to accomplish what I had set out to do, but I recommend an 80x60cm table frame (200.805.57) and the extension frame (100.568.88) for anyone else wanting to duplicate this.

Step 2 – Prepare the lower shelf for the upper desk supports

Unpack the two extension tables (901.052.67) and place them bottom-up and lengthwise to create a 160x60cm surface. The arrangement should be such that the pre-drilled holes will line up with the screw holes in the lower frame. Lift the lower frame up onto the extension tables to verify this and adjust the arrangement of the tables as required, but do not attach the lower frame yet.

Once this is done, go to each end of the lower frame and locate the holes where A-legs would normally be attached. These are located 7cm from the edge of the frame on either side of where the T-legs are to be mounted. Use a pencil to mark the corresponding location on the bottom of the extension tables. Then, remove the frame and use a 3/8″ drill bit to bore holes through the extension tables where the marks were drawn.

Step 3 – Assemble the lower shelf

Attach the T-legs to the lower frame and attach the lower frame to the extension tables per the Galant instructions. When complete, set the lower shelf on its legs.

Step 4 – Create the supports

Open the first box of Capita legs (200.495.38) and remove the legs and four plastic caps.

Remove the base from each leg. They are snug and it can sometime take a bit of effort to detach them. Use the 3/8″ drill bit again to bore a hole in the centre of each base. Clean off any excess plastic and re-attach the bases to the legs.

Insert a threaded rod into the base of each leg and screw it into the upper thread so that 9cm (3.5″) of rod protrudes from the base. Screw the plastic cap provided onto the threaded rod at the top of each leg.

Step 5 – Attach the support to the lower shelf

Place one of the supports in each of the drilled holes in the lower shelf. The threaded rod at the bottom should protrude through the A-leg holes in the lower frame. Secure each rod to the lower frame with a 3/8″ nut.

Step 6 – Attach the upper frame to the supports

Place the upper frame (000.568.84) onto the supports using the same A-leg holes. Secure the upper frame to the supports with 3/8″ nuts and tighten both the upper frame nut and lower frame nut to the point where the Capita leg will not turn. Be careful that the threaded rod does not extend beyond the thickness of the upper frame’s nut.

Once complete, use a grinder tool to cut off the excess threaded rod below the lower nut.

(Note: A 10″ long 3/8″ bolt might also be sufficient to assemble the supports without the mess of grinding off the threaded rod, but I haven’t actually tried this.)

Step 7 – Attach the upper desk to the upper frame

Attach upper desk to the upper frame per the Galant instructions.

Step 8 – Assemble the monitor shelf

Open the other package of Capita legs and attach them to the four corners of the Ekby Hemnes (301.798.74) shelf. Place the assembled shelf toward the back of the upper desk.

~ Jody Lemoine, Niagara-on-the-Lake, Ontario, Canada

More hacks on IKEAHackers.net
Bunny Do!
My Expedit computer desk perfection

The Author

Jules IKEAHacker

"I am Jules, the engine behind IKEAHackers and the one who keeps this site up and running. My mission is to capture all the wonderful, inspiring, clever hacks and ideas for our much loved IKEA items".

17 Responses to Galant Standing Desk with Monitor Shelf

  1. Max Jost says:

    Hi, nice work :) But which type of screen do you use?

  2. I really like the look, but I’d suggest to replace the lower shelf with a slide-out keyboard tray.

  3. Mark says:

    Have you mastered the content of those books? Or are you like me and only remember less than 1% of what’s in them? Never did get my CCNA :(

  4. Anonymous says:

    How much did this cost?

  5. NonnyMus says:

    Nice job. The human skeletal system isn’t designed for long-term standing, so take care to not damage your back, knees, hips and feet. Use anti-fatigue matting underfoot and remember to shift your weight from foot-to-foot as you work. Be especially careful if joint problems run in your family, you have injuries, have a big stomach or you have joint abnormalities. I wasn’t and am suffering for it now!

    If you can install a treadmill and walk at low speed while you work, you’ll be better off. Humans can walk for hours without damaging themselves. Standing? Not so much.

  6. Cubicle says:

    This is an awesome use of materials to create an amazing desk.

  7. Anonymous says:

    Was your decision to have the lower frame be smaller than the upper frame structural or aesthetic?

    • Jody Lemoine says:

      Structural. I considered having a full-depth lower shelf, but realized that I would be hitting it with my knees a lot. Using the smaller lower frame gives me some more clearance.

  8. Steev Kelly says:

    Looks Great! I’m glad my hack inspired others to stand up! I like the use of the capita legs as the risers instead of the plastic PVC – I may have to go back and re-do mine now!

    • Jody Lemoine says:

      Thanks! I really liked your idea of the two-level desk, giving lots of storage underneath. I haven’t used the storage as much as I thought I would, but it makes for a good out-of-the-way space for my switches and such.

  9. Adam Hough says:

    Thank you for the excellent design and build process; I’ve been using pretty much the same design for my work desk (for about a year now) based on what you wrote. It’s been sturdy and functional!

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

Back to Top ↑

  • Null
    Null
    Null
    CoverCouch
    Null
    Overlays

  • Knesting

    Covercouch


  • See the Best of the Best

    See the Best of the Best

Twitter Auto Publish Powered By : XYZScripts.com