Bathroom caddymedicine

Published on October 16th, 2012 | by Jules IKEAHacker

6

Tub Caddy Medicine Shelf





Materials: 2 Molger bathroom organizers, several chunks of scrap wood, measuring tape or yardstick, 1000 grit wet/dry sandpaper, plexiglass, screws (molly bolts if needed), drill, hammer and a nail, screw driver, level, and adhesive rubber shelf stoppers

Description: 1. Lie the two Molgers next to one another on their long edges. You have the option of either creating shelving so that the inside “basket” of the caddy faces inward or outward. Just be sure to be consistent when drilling your holes. Using the drill, prep your Molger bath caddy by drilling two holes 8 1/8″ apart on one of the long sides of the caddy. Repeat on the other caddy. I found it helpful to stuff some blocks of spare wood under the edge on which I was drilling.

2. Hold one of the Molger against the wall vertically and, using the level, mark where it will go. Don’t forget to mark your hole locations on the wall! Hold the opposite Molger the desired distance away from the first marks, and mark where it will go, as well.

3. Drill holes into your wall. Insert molly bolts if they’re needed.

4. Screw the screws part way through the holes in the Molgers and then line them up with the holes in your wall. Screw the Molgers into your walls. Be sure that they’re facing the same direction (“basket” in or “basket” out)!

4. Once they’re up, use your measuring tape or yardstick to determine how wide your plexiglass shelves will need to be and how many you’ll want. You will want some of the plexiglass to stick out beyond the slats so that the shelf will stay in place. For example, from inner edge to inner edge, my Molgers are set 11 1/4″ apart, but I opted for 15″ shelves so that I’d have some overhang.

5. Regardless of how long you want your shelves they will need to be 4 1/2″ wide. If you purchase your plexiglass at Lowes, they will cut it for you for free. Home Depot is not legally allowed to cut plexiglass anymore, but you can still purchase it there. I chose to have a Lowes employee cut it for me.

6. Once your plexiglass is cut, sand the edges with your 1000 grit wet/dry sand paper. First do it dry, then finish off with a wet sand. If your hardware store doesn’t have 1000 grit, try an auto supply store (it’s used for buffing headlights).

7. Slide your plexiglass shelves into the Molgers, resting them on the slats at their desired heights. You can stick the adhesive shelf stoppers to the underside of each shelf on either the interior or exterior, so long as you’re consistent. This will prevent the shelves from randomly slipping out.

~ Stephanie

More hacks on IKEAHackers.net
Large Expedit Vinyl / Turntable Shelving
This Old House does an Ikea Hack!!
We will be moving. Don’t miss any hacks.
Be the first to know
IKEAhackers will be moving. Be the first to know of the new domain when it is ready. Enter your details and sign up now.


The Author

Jules IKEAHacker

"I am Jules, the engine behind IKEAHackers and the one who keeps this site up and running. My mission is to capture all the wonderful, inspiring, clever hacks and ideas for our much loved IKEA items".

6 Responses to Tub Caddy Medicine Shelf

  1. Anonymous says:

    Why?

    • Elle says:

      Why not?

      I like the look of it and it appears to me this would be cheaper than buying a medicine cabinet of a similar size. The bath caddies are $10 USD each and that small amount of plexiglass is probably ~$20.

      Another benefit I thought of right away, is the width is totally adjustable. My bathroom wall is slightly larger than the one shown here so I could make my shelves about 5″ longer (and I’d be sure to get a thick enough plexiglass to support weight in the middle, especially if I went even wider).

    • Stephanie says:

      You’re right, Elle, it was cheaper for me to do it this way. In all, I spent about $35 on materials, and I got a sweet custom look. The medicine cabinet I had been looking at cost $50 before tax, and it had lots of glass shelves I knew would end up broken (because I’m a super klutz).

      The plexiglass is 1/4″ thick. I wanted it to be able to hold heavier things (like a full bottle of mouthwash) without buckling or bowing under the weight.

      Now I have something I can adjust however I see necessary. I can even purchase tinted plexiglass and make colorful shelves. In fact, that would be a good idea if you were putting this in a kid’s bathroom.

  2. Mélusine says:

    Very nice idea, love it!

  3. Anonymous says:

    Very clever, and good looking too!
    Love that not only can the number of shelves change depending on need, but the width of the shelving can be customized to fit a given situation.
    The handle turned towel bar: Sweet!

    • Stephanie says:

      The “towel bar” was an unforseen and happy accident but totally a bonus considering the only other towel bar is across the bathroom over the toilet.

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

Back to Top ↑