Featured

Published on August 31st, 2012 | by Jules IKEAHacker

21

Hyllis Catwalk





Materials: Hyllis shelving units

Description: Use Hyllis shelving units to create a literal “catwalk” for your cats!

Writing up a good set of directions to do this is almost as hard as hanging the catwalks themselves. I’ll do my best to make it clear but if you undertake this project then know that it will take a lot of patience, sweat, a good eye/mind for hacking.

Step 1: Take a look at your ceiling and determine where you want the catwalk to run. I did this on a flat drywall ceiling which was hard enough. You could conceivably do it on other ceiling material like wood but I’ll leave that up to you.

Step 2: Get your Hyllis shelving units. Each Hyllis unit gives you just under 8ft of catwalk length when the four shelves are laid out end-to-end. If you are making a corner turn that will cut it down roughly a foot per turn.

Step 3: Gather all the other materials you will need. You will need a lot of threaded bolts. I used 1/4 but you could use anything from that size or larger to keep the walks steady. If you can, buy the threaded bolts in lengths that you can cut in half so you can get two poles out of one, but make sure they are long enough to reach into the drywall with a toggle bolt hanger and still give enough height clearance for the cats to walk beneath the ceiling. I used at minimum two bolts per shelf sometimes using three or four if I was making a turn and need extra stability or at an end point. You will also need toggle bolts that match the thread of your bolts. Get a lot of appropriately sized nuts and washers. Each hanging pole will require: 1 threaded bolt, 1 toggle bolt, three washers, three nuts. You will also need some sort of light weight board to place inside each Hyllis shelf (the shelves are flipped upside down and the boards placed inside them). I used cheap particle board. You will also need some low adhesive spray and lots of drawer liner for the final grip pads on the walk.

Step 4: Make a template! Get a piece of poster board and cut it to the exact size of one shelf. Mark the template with your spots for the hanging bolt holes.

Step 5: Start cutting your boards for the shelves so you can just grab a new one and go. Don’t drill all the holes yet. Only do that a few at a time just in case you have to make a change of direction. Drill your first shelf, making two holes on one end and one on the other. Make the holes just large enough to fit your bolt. Thread a nut at the bottom of the bolt and one at the top. Place a washer under the bottom nut and one on the top. Place a toggle bolt on the top with some bolt poking through the top. And then put the bolt through the shelf hole and place another washer then another nut. So the sequence of layers for each hanging bolt will be like this from top down: TOP small space-toggle bolt-small space-washer-nut-large space-nut-shelf-washer-nut BOTTOM

Step 6: Determine your starting point for the first shelf. Assemble one shelf with three bolts (two for the end). Hold it up to the ceiling and do your best to mark the spots where the toggle bolt will enter the ceiling and the bolt will stay upright and level as possible. Mark the three spots. Get a drill with a bit smaller than the size of your bolt. Use it to probe your ceiling at your marks to make sure you are not going to hit metal or wood. You can also use a stud finder to help out. If you do end up hitting wood you can still make it work by either drilling (with the appropriate bit) deep enough to get a toggle bolt all the way through the wood and using a longer bolt or you can use an adapter to combine a small screw tip to the end of your bolt (you should be able to find these at a big hardware store) Luckily I only had to do this a few times.

Step 7: I suggest buying cheap plastic paint throw covers and some good tape to hang all around the ceiling area and walls/floors of the areas you will be working in. Drilling this many holes in the drywall creates a lot of dust! So be careful and patient. Might be a good idea to get a breathing mask too. Drill at your marks and push your toggle bolts into the ceiling keeping the shelf as level as possible. Once you are sure the toggle bolts are secure then tighten all the nuts while still keeping the shelf balanced and level. The shelf will be a little wobbly for now. Don’t worry about that. Later you will use the Hyllis legs that came with the unit as side pieces to secure multiple shelves together making the catwalk tight and stable.

Step 8: Assemble a second shelf and hold it up next to the first one and repeat. At corners you can use L-brackets to secure the shelves together. I also used a few larger L-brackets for the section of the walk that was close to the wall. Once you have enough length you can then place a Hyllis leg on each side of the shelves using a very small drill bit and wood screws to secure it to the shelves. You may have to cut the Hyllis legs to match the length of your walks.

Step 9: Once all the shelves are hung and secured with the side Hyllis legs then you can cut drawer liner with scissors and razor blades to fit the shelves and spray the back of them with a low adhesive glue .

Step 10: I installed a mini rope light down the length of my walks. And I used Ekby shelves as steps for the cats to make easy jumps to the catwalk entrances.

See more photos of the Hyllis catwalk.

~ Jason, Texas

More hacks on IKEAHackers.net
Very Effektiv Garbage & Recycling Bins
Baby Karlstad corner sofa

The Author

Jules IKEAHacker

"I am Jules, the engine behind IKEAHackers and the one who keeps this site up and running. My mission is to capture all the wonderful, inspiring, clever hacks and ideas for our much loved IKEA items".

21 Responses to Hyllis Catwalk

  1. Anonymous says:

    I LOVE THIS.
    -carmen

  2. I LOVE THIS too.
    ist cat-tastic!!

  3. Anonymous says:

    At last! Someone who is as crazy (about their cats) as I am. A beautiful job!

  4. This is probably the most original idea and hack I’ve ever seen! It’s brilliant!
    The home is beautiful and this gives it a unique look as well.
    At first glance I thought it was for your wires or home automation…I’ve done work in the post production industry, where there’s catwalks which carry millions of wires traveling throughout the building…this would also work wonderfully for a smaller facility that needs to do these kinds of mods on their own! (regardless of whether they have actual cats).
    Great job! (love “Cat-Tastic”!)

  5. Anonymous says:

    If only I could talk my girlfriend into letting me do this for our cat! I have tried several times but to no avail.

  6. Anonymous says:

    Fabulous and it fits well with the house decor, not an obvious cat structure. Many cats love heights so this is a dream. Now you need more than one cat to enjoy it.

  7. Anonymous says:

    Haha amazing! Really love the idea.

  8. Anonymous says:

    Meow! Two paws up!

  9. Olivia says:

    I hope your cats give you all the love you deserve and more, because this is awesome!

  10. Anonymous says:

    So cool!

  11. Anonymous says:

    FANTASTIC!!!

  12. Anonymous says:

    In my next life I want to come back as your cat.

  13. Anonymous says:

    Fantastic idea, really! I’m just thinking about the first time one of my cats decides to rid themselves of a hairball from the catwalk.

  14. Anonymous says:

    This is awesome! Once your cats are in the air like that its easier to hit them with the airsoft pellet gun!!

  15. mvankipu says:

    Too bad I can’t do this in my apartment. If I ever own my own place this is the first thing I am going to do there. Such a great way to incorporate mood lighting too!

  16. Great hack Jason! I love the industrial look with the galvanized finish of the HYLLIS, and the installation is much more elegant than similar setups I’ve seen. *=8^O

    I stumbled on this hack while I was poking around for ideas for the too-small-for-a-bedroom that we want to turn into a cat room with a catio (cat patio – the TSFAB window will open up into the catio which will be an extension of our deck that we also need catwalks/perches for) for our 3 cats (one is a large Maine Coon mix and weighs about 15 lbs).

    We’ve retired, downsized and are updating a nice little 30 year old mobile home. The soft-panel ceiling wouldn’t support this setup, but it looks like this catwalk could be modified to be wall mounted. One of the re-purposed legs could be mounted to the wall with holes drilled in it. The question becomes what to do for the other side support. Also, we would have to figure out how to install “passing lanes” so that they don’t knock each other off in passing.

    I do have some questions: What distance between the catwalk and the ceiling did you settle on? Does your cat have to crouch when walking on it? What was the thickness of the particle board that you used to fill in the shelves?

  17. Anonymous says:

    wow,I used to think our cats are lucky cuz we spoil them. Now your cat is the luckiest! Great job and cute kitty!

  18. Beaufort says:

    Ingenious! =^..^=

  19. VCann VCann says:

    that is one demanding cat.

  20. SockNinja says:

    Love this hack, but the red lighting makes it look tacky IMO. Soft white light would have been so modern, clean and romantic with a good dimmer ;)

    For you not your cat…lol

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

Back to Top ↑

  • CoverCouch
    Null
    Null
    Null
    Overlays
    Null

  • Knesting

    Covercouch


  • See the Best of the Best

    See the Best of the Best

Twitter Auto Publish Powered By : XYZScripts.com