Materials: dunno, help me!!
Description: I love my IKEA sofa, but I do not love how the slip covers tend to....uh...slip so easily on the cushion.
Friends of mine who also have furniture from IKEA are also frustrated by this.
Anyone have a solution?
Thanks!
~ Steven
You could try some small pieces of velcro on the inside of the cover and on the cushion.
ReplyDeletewas about to say the same then Nani. Velcro should do the trick.... I'd probably use a 2 to 3 cm width one and put it along the major seam (the one that slipped on the picture).
ReplyDeleteHave you tried non slip rug pad sections towards the back side of the cushion?
ReplyDeletei have the exact same problem with my kivik. I would not buy this sofa again.
ReplyDeletevelcro sounds goot on first look. But the cushion itself is really sticky... I dont think velcro is really much stronger.
YES! I have this same problem and I don't think the velcro would work. I wouldn't trust the adhesive and sewing it on the slip cover is easy, but not so with the foam.
ReplyDeleteWHAT TO DO?!
Try double face tape for fabirc.
ReplyDeleteI THINK wrapping a layer of batting (see JoAnn Fabrics) around your bare cushions might help. It might also add a little umf to your cushion as well.
ReplyDeleteI'm curious.. I have the same trouble with same fabric. At Ikea store the sofa not look that.. It was the cheaper fabric with cotton. Anyone have this fabric???
ReplyDeleteMaybe crepe tape could work?!
ReplyDeleteTry good old fashioned diaper pins. Regular safety pins tend to be too small & can pop open at unfortunate times, but diaper pins are large, sturdy, & designed to stay closed until you open them. When you put the slip covers on, use 2 or 3 diaper pins per cushion, seam-to-seam in a row in an unseen location, like the bottom back seam.
ReplyDelete^^ diaper pin suggestion is spot-on. I use a similar trick to keep duvet covers from sliding around on my comforters.
ReplyDeleteI hate to shoot down good suggestions but everything suggested so far will show.
ReplyDeleteI get a sheet of the rubber cabinet liners and place a large sheet on the pillow before putting the covers on and the NEVER move. Cheep, can't be seen, and works.
You need to purchase some upholstery spray adhesive which will provide some tack or hold in that area. Any fabric or upholstery shop will carry it, try Walmart in their Automotive section. Just don't buy any kind that provides a permanent bond. Most all purpose fabric and foam spray adhesives provide a tack similar to rubber cement where it bonds but you can peel it off.
ReplyDeleteYou will then remove the cover from the cushion and leave it inside out. Then LIGHTLY spray the problem area (as in your picture & I would also do about 1/4 of the way back at the top & bottom of same area). They put the cushion back on while inside out bonding the glued areas first as your turning it back inside out (make sense?).
I would however launder them first if you haven't yet because that may just take care of the slipping problem.
Reasons for rolling or slippage is do to either loose fit or not enough grab or both.
Also TEST A SMALL OUT OF THE WAY AREA FIRST and wait for it to dry to see how it reacts and make sure you buy CLEAR
spray!!!!!
This is how Upholstery, Automotive & Boat Interiors take care of the "Roll & Slip"
Good Luck
Not much of a solution. But we just flip the cushions... then it will work its way back.
ReplyDeleteWe do the same. Every 2 weeks and it works.
DeleteIt seems that most of you dont have an kivik or karlstadt sofa. the cushion is already very very very sticky. but it still moves. it takes weeks. but finally it moves.
ReplyDeleteso i bet spray adhesive, double sticktape and velcro wouldnt do the deal. the big security pins sound good. but where do we put them in? the foam isnt strong enough to hold it.
I have a karlstad sofa with grey covers that you're not supposed to wash according to the instructions. But I have (several times), and they shrink just enough to take care of the slipping problem for me.
ReplyDeleteI have Karlstad sofa and I've noticed that it makes a difference which side you put the big pillows into their covers. Try to unzip them, wash and iron them, then remember the current position and put them back in the opposite way - you may first try to simply put them the opposite way, I mean the other end, and see if it works.
ReplyDeleteI noticed that I had this effect similair to on your photo "bad" and then I switched them around and it was good. Hope it may help you. Try it out, at least.
Try those mats that go under rugs to keep them from slipping.
ReplyDeleteFirst of all, this is not just a cheap-IKEA-sofa problem - cover-slipping happens to pricier sofas too. Ultimately it has to do with the forward/downward force exerted on the front half of covers when you are sitting on or getting up from the sofa.
ReplyDeleteThe simplest solution is to flip the cushions every one-two weeks so that the covers are pushed back/forth on an equal level. Of course, this is only possible if the cushions are flip'able - either directly or by swopping cushions/covers. This would work even if the cushions/covers have a backside (underside? ) not meant to be seen - you just have to accept what it looks like while you are moving-by-sitting-on the covers back in place.
The muscle-powered solution is to manually move the covers back in place. That requires a good old-fashioned beating of the cushions to get them back to their pre-I've-been-sat-on shape and strong arms for pulling/forcing the fabric back. (Sofa-cushion-fabric is often heavy and stubborn). The problem is, though, that if you don't do this at reasonable intervals, the fabric may already have been stretched sort-of permanently.
The final solution is to somehow fixate the covers to the cushions, like previous posters have suggested. It's not a bad idea per se, but what you have to consider is that the downward/forward dragging of the covers will still be there. If you fix the covers with pins, the dragging force held back by the pins may eventually ruin the fabric where the pins are placed. The spray-glue/adhesive/rubber-friction method is perhaps better because it distributes the stress over the whole cover-cushion interface.
I would not recommend pins as it would create holes in the foam rubber where it would pull as it rolled. Velcro or double sided tape would end up rolling also, same as the slipcover.
ReplyDeleteIf the covers are the washable type and they have not been washed yet I would wash them as they will shrink slightly and probably be snug enough to prevent the slip/roll thing.
If they still slip then adhesive is the only thing that will prevent it. Its what the Upholstery industry uses whether they are upholstering an item or simply slip covering it...the principle is the same.
Pins do not work because the foam isnt sturdy enough to hold them.
ReplyDeleteVelcro was my first idea, but theres no way to attach the velco to the actual cushion.
We did wash and dry the covers (even tho the tag says dry clean only) and they did shrink a bit. It definitely helps, although they do still slip some, just not as easily. Also, you can tell that the cushions are a little smaller than they are supposed to be.
Im gonna try wrapping some rubber rug mat material around the cushion and then put the covers on. I think doing that, plus the slightly shrunken fabric should do the trick pretty well.
Thanks for all the responses :)
What about bedskirt pins? I use them to keep my bedskirt from moving all over the place. They're cheap and you don't have the problem of safety pins that won't grab.
Deletehttp://www.bedbathandbeyond.com/product.asp?SKU=10995680
There is a 10 year warranty on those sofas, so if your sofa is not yet that old, maybe you could try to see with Ikea?
Delete1. Well made cushions are 25mm (one inch) bigger in every direction than the covers. That way the fabric remains taut & grips.
ReplyDelete2. The foam filling is covered in calico or padding & calico.
3. The seams have piping cord to strengthen them.
In short, borrow a book on upholstery or slipcover making from the library & see if the Ikea cushion padding comes close to best practice.
It won't. (I'm about to make new covers for Ikea chairs)
Consider getting new cushion filler.
BTW don;t wrap rubber around the filler as this will make them uncomfortable to sit on.
i'd like to find someone who makes a cover for the manstad sofa :/
ReplyDeleteturn the cushions over every day, the cover will slip back the other way.
ReplyDeleteBemz.com makes covers for the Manstad sofa
ReplyDeleteYikes, seems so expensive.
Deleteput a board (same dimension of the cushion) inside at the bottom of cushion.
ReplyDeletethe spray adhesive idea is nice and works.
ReplyDeletewrapping some batting around the cushions, and washing the covers before putting them back on will do the most good, though.
IKEAs cushions are a bit smaller than they probably should be, but most manufacturers make their cushions too small because it saves them a few cents on the dollar on foam, which is expensive.
take it from an upholsterer's daughter :: wash the covers and wrap those cushions in a couple layers of batting before you put the covers back on. the seat'll be more comfy, and the cover'll stay in place better.
i like that article..thanks
ReplyDeleteIn my experience with Ikea's Ektorp sofa, the problem seems to be that the foam cushions aren't dense enough and --for the lack of a better word-- smush down over time. Washing the covers in warm or hot water helps for a week or two because they are tight again, but the firmness doesn't last long. I've tried the batting trick, but you don't get the crisp cushion edges you want.
ReplyDeleteIf you look at the Ikea sofas for sale on Craigslist, it's usually only the smushed cushions that show any wear. The sofas, themselves, are very well built and will last a very long time with proper care.
I suggest saving up for dense, professional upholstery-grade cushions. I've replaced mine, and I'm extremely happy with the result. Now, the cushion covers fit beautifully, just like they did when I bought the sofa.
Hope this helps.
To keep the slip covers from slipping: Safety pins along the zipper seam, through the seam and into the cover for the cushion. Worked for my sofa and armchair.
ReplyDelete