Lack

Published on July 21st, 2010 | by Jules IKEAHacker

7

Lack wall mounted home Theater





This is really just a modification or practical application of wonderful hacks that I found on this site. I take a step further by incorporating moderate handy-man skills to turn just a few bucks of Ikea stuffs into a real slam of a home theater system.

before

I used the Lack long and medium shelves to build the frame, and the Lack side table to do the entertainment center. The wires go into the wall behind the TV and come out on the OTHER SIDE in my bedroom near the baseboards, travel to the far wall, then return behind the bikes, and run below the heaters all the way to the entertainment center. (A little less than 50ft of cable for each device.)

The whole home theater is no more than a 5.1 stereo with optical input, a PS3, a Wii, and a DVR hanging from brackets under a Lack side table, with some 50ft of cables running to the TV, but stashed in the wall. The TV is then framed as you like with the Lack medium and long shelves.

I should be clear that I think that any Ikea furniture in the Table/Shelf arena needs a fresh coat of paint. Ikea’s veneer will bubble quickly if you put something hot on it, or will scratch easily and look unsightly. I put a polyurethane coat of black, high-gloss enamel. (Took 30 minutes once I laid down a tarp. This coat makes it shiny, looks nicer than the stock paint, and protects it incredibly well from just about everything.

The entire project took 8-10 hours, and required the following tools:
Lack side table and Lack wall shelves
Hand Drill with bit-set
Paint, pan, tarp, roller
L-brackets, heavy copper tape, aluminum dowels. (For the side table
dry-wall saw (it’s like a really skinny hand saw that you can punch through the wall to start)
Chisel (to cut a trench in the drywall)
A HEAVY DUTY extension cord (to lay in the trench)
Spackle… lots of it, to hide all your destruction from the Super.

To do the entertainment center, use L-brackets attached to the legs, measured for the height of each component and screw them into place. You will likely find that your conmponents aren’t long enough to use the same technique for the back, so instead hang a heave copper or metal tape from the middle of the table on the sides, then drill holes and run a metal or wooden dowel across, supporting the back end. Here is a list of other things that I used from Amazon.com.

OUTLETS
2x Datacomm Electronics 45-0001-WH Gang Recessed Cable Plate (White)
Datacomm 50-3321-WH-KIT Flat Panel TV Cable Organizer Remodeling Kit with Power Outlet (White)
(It is important not to illegally, or dangerously run electrical cables behind the wall. It’s against code, and maybe mice or space rabbits will nibble on them and cause a fire, I’m still unclear. Instead install an electrical outlet where you want it. It was done like so:
1) Mark where you want your TV to go, hopefully directly above the electrical outlet near the floor (so 90s)
2) Use a box cutter and chisel to dredge out a 1/2-3/4″ deep cavity that you will run a wire in and staple into place.
3) Wire the positive and negative leads to the corresponding outlet below, and then to your new one as you set it in place.
4) Lock the box into place by following the directions like an adult. Don’t wing it, you’ll regret it.
5) Punch a hole on the other side of the wall near the floor and install a cable-hiding-wall-plate to pull the cables through.
6) Same hole-punching to bring it back across and run it along the baseboards to your entertainment center.)

CABLES
Steren RGB RCA Coupler – 3 x RCA Female to 3 x RCA Female – Plastic
RiteAV – SVGA Monitor Cable with 3.5mm Audio – 50 ft.
50 FT 3-RCA Stereo Audio Video A/V AV Cable Patch 50ft
2x HDMI M / M Cable, 50 FT / 15 M
Wii Sensor Bar Extension Cable, 50 ft
16 AWG Flat Speaker Wire 100 ft.

TIES
Zip Tie Mount, 1/2 X 1/2, 25 Pack (These are essential when dealing with long cables.)
Nylon 6/6 Self Locking Cable Ties 8″ L, 2″ (Pack of 100)

More hacks on IKEAHackers.net
Benno dvd tower headboard and room divider
Old bathroom, small restoration

The Author

Jules IKEAHacker

"I am Jules, the engine behind IKEAHackers and the one who keeps this site up and running. My mission is to capture all the wonderful, inspiring, clever hacks and ideas for our much loved IKEA items".

7 Responses to Lack wall mounted home Theater

  1. Bradford says:

    What paint did you use and what type of roller? The finish you got it so amazing you’d never know it wasn’t a factory finish – as I’m doing something similar knowing the right products to buy would be of immense help, thanks!

  2. Anonymous says:

    Hi

    Looks good but I’m more interested in how you’re keeping your bikes out the way.
    Care to enlighten us please?

  3. Anonymous says:

    Nice hack.

    How well does your PS3 controller respond since it’s in another room?

  4. Shrike says:

    Whoa, I found my weekend project. That Lack table A/V rack is just what I’ve been looking for =)

  5. Zorbo says:

    Love the framing of the TV well done!

    only question is wow, 50ft of cable per device… are you getting any losses in terms of picture quality or wii lag?

  6. AnnaTheRed says:

    I did this hack and just blogged about it! (and some)

    http://www.annathered.com/2010/08/09/ikea-hack/

    I just wanted to mention the legs of LACK table are hollow inside, so don’t be surprised when you’re pre-drilling holes.

    Thank you for the great hack!

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

Back to Top ↑

  • CoverCouch
    Null
    Null
    Null
    Overlays
    Null

  • Knesting

    Covercouch


  • See the Best of the Best

    See the Best of the Best

Twitter Auto Publish Powered By : XYZScripts.com